How to Maintain your Airsoft Gun – Clean, Lubricate and Care

Whether you are new to the game or a seasoned competitor, knowing basic airsoft gun maintenance can save you fourth dimension, frustration, and money.

how to maintain your airsoft gun

Caring correctly for your gun will allow it to concluding for y'all years, avoid unnecessary clothing and tear, and help yous when faced with technical difficulties in a game or competition.

Hither are easy-to-follow steps on how to clean an airsoft gun.

How to Maintain Your Airsoft Gun

Before you showtime leaning about maintenance, you lot should be aware about the common types of airsoft guns by checking out our guide on Airsoftpal. Figure out which gun you have, and acquire how it operates. Knowing this information can make it easier for you lot to troubleshoot when having problems with your gun, and salvage you money you would otherwise spend if forced to accept information technology to a professional.

There are two types of guns well-nigh common to airsoft – They are spring loaded and gas-powered.When you pull the trigger on a leap loaded gun, the tension in a spring is released into a BB or a pellet. This causes the gun to release the BB at a high-velocity. A bound-powered gun is limited to shooting single-fire only.

When the trigger is pulled in a gas-powered airsoft gun, a hammer inside of the gun will push against the valve in the mag. This causes the gas to be released into the pinnacle portion of the gun, shooting the BB out of the chamber.

How to Clean your Gun Barrel

Airsoft butt cleaning is easy. If your BB's are diffusive vertically when firing your gun, it is fourth dimension for a good airsoft butt cleaning. You lot but need a cleaning rod and newspaper towel to practise this.

  • Thread a strip of the paper towel through the tip of the cleaning rod
  • Spray a silicone lubricant onto the strip
  • With the strip first, insert the cleaning rod into the barrel
  • Motility and rotate the rod down the barrel and repeat until clean

Check out this video for more than advice on cleaning your butt:

Lubricate your gun

If yous are having a problem with your gun misfeeding or jamming, the offset matter yous tin do to troubleshoot is to lubricate your gun. Start by removing your mag and burn your gun in semi-motorcar mode a few times to make sure information technology is free of BB's. Flip the gun upside down and spray silicone oil into the hop. Get out it upside down for a few minutes to allow the oil settle.

If the gearbox needs to be lubricated you need to remove the motor, locate the small pigsty at the bottom of the gearbox, and spray the silicone oil into it. But like the hop, exit it upside downward for a few minutes to make sure all of the oil seeps in.

Maintenance tools

In caring for your gun you volition want to use the proper tools. Proper fitting Phillips and hex wrenches will keep screws on essential parts of the gun from stripping out. Y'all may pay more than in the long run past purchasing inexpensive tools that finish up wearing quickly and ultimately- breaking. They can also impairment your gun.

Essential tools to acquire are every bit follows:

  • Hex drivers– Hex head fasteners can be found in almost every airsoft gun. They range in sizes and information technology is important to find out what the corresponding size is for your gun.
  • Screwdrivers– Stripping the heads on the screws in your gun can be detrimental. You likewise need to make certain yous have the correct size screwdriver for your gun
  • Nut drivers– This is non necessary for all guns but tin be used in securing the piston head to the piston.
  • Hand tools– You lot may need to charge the battery connector to your favorite manner or re-wire an AEG. In such cases, you'll want to take pliers and wire cutters on paw to handle it.
  • Sharps– Picks can help provide you with easier access to difficult to accomplish places.
  • Knife – A hobby knife can aid in carving plastic pieces.
  • Greases and oils– Proceed a thick grease to lubricate your gear sets. Lithium grease tin easily exist found at most hardware stores and works well for this. For rubber components such as o-rings and hop up bucking, a silicone oil is commonly used.
  • Toolbox– Keeping track of your things will make it easier for yous to more effectively address your problems. It will also save yous a lot of money since you will exist less likely to misplace your tools.

Airsoft Magazine intendance

Depending on the type of gun yous ain, magazine care volition vary. If you take an electrical or spring airsoft gun, brand sure yous empty the magazine completely after each use to preserve spring strength thus, preserving the shelf-life of your gun.

If you have a gas airsoft gun, leave the magazine pressurized. Calculation a driblet of lubricant on the internals will aid keep all components intact. When you expel gas from the gun, exercise not employ the release valve. This will crusade the o-ring to freeze and tin crusade gas leakage in the future.

How to unjam your gun

Jams can happen for many reasons. Excessive clay or droppings inside of the butt, dirty or deformed BB'southward, an accumulation of dirt in the magazine, damaged nozzles, or a damaged hop tin all cause the gun to jam or misfire.

If the gun is jammed, yous demand to troubleshoot the problem immediately to foreclose any damage. Plough off the hop up, insert the opposite end of a cleaning rod into the barrel, turn the gun upside down, and push the BB back into the magazine. If that doesn't solve the problem it is a good idea to have the gun to a professional person.

The practice'south and don'ts of airsoft maintenance

DO

  1. Leave a pocket-size amount of gas in the magazine- this will go along the o-rings lubricated when the gun is not being used for an extended period of time.
  2. Make sure you clean AND lubricate your airsoft gun every 1 to ii months after every game or match.
  3. Avoid weakening the recoil spring by making ensuring the slide is not fully retracted for long periods of time.
  4. Avoid weakening the follower spring by emptying your magazine before letting your airsoft gun sit for a while.

DON'T

  1. Don't release all of the gas in the magazine past pressing the release valve. This will pb to permanent leakage caused by deformed and frozen o-rings.
  2. Do not slam the magazine into the gun. The magazine lips and nozzle in the slide will break every bit a result. Your gun will so misfire.
  3. A modest amount of gas left in the magazine is good merely a mag left full of gas will cause the o-rings to deform
  4. Don't operate an airsoft gas gun in cold weather as this hinders functioning.
  5. Don't rapid burn down- it will cause the o-ring to freeze.

While learning how to make clean and maintain an airsoft gun may sound intimidating and time consuming, it'due south really very simple and helps to ensure that your weapon volition be performing at its highest level, lasting y'all for years to come.